...
To delete a process unit, click the delete icon or red "x" “x” located in the last column of the table.
| Wiki Markup |
|---|
{composition-setup}{composition-setup} |
Click image to expand 
| Wiki Markup |
|---|
{cloak:id=PNG1|cloak.toggle.type=none| |
| Cloak |
|---|
cloak.toggle.zone=true} | true
| Panel |
|---|
Image Added |
| Wiki Markup |
|---|
{cloak} |
| id | PNG1 |
|---|
cloak.toggle.type | none |
Step 2: Indicate CEMS utilization for the process unit
...
| Note |
|---|
Note that when adding a new process unit you are prompted to answer the CEMS question immediately (the answer to this question will default to "No" “No” for process unit added using the "ADD “ADD a Unit" Unit” link and will default to "Yes" “Yes” for units added using the "ADD “ADD a CEMS Unit" Unit” link). |
The CEMS response may be changed here and the process unit information will be relocated to the appropriate table on the Subpart Overview page.
When finished, click SAVE.
Click image to expand 
| Wiki Markup |
|---|
{cloak:id=PNG2|cloak.toggle.type=none| |
| Cloak |
|---|
cloak.toggle.zone=true} | true
| Panel |
|---|
| id | PNG2 |
|---|
| cloak.toggle.type | none |
|---|
Image Added |
Step 3: Select calculation methodology
...
When finished, click SAVE.
Click image to expand 
| Wiki Markup |
|---|
| Cloak |
|---|
{cloak:id=PNG3|cloak.toggle.type=none|cloak.toggle.zone=true} | true
| Panel |
|---|
Image Added |
| Wiki Markup |
|---|
{cloak} |
| id | PNG3 |
|---|
cloak.toggle.type | none |
Step 4: Define the process unit
...
To add an input or an output, click "Add an Input" or "Add an Output" below each respective table.
Click image to expand 
| Wiki Markup |
|---|
{cloak:id=PNG4|cloak.toggle.type=none| |
| Cloak |
|---|
cloak.toggle.zone=true} | true
| Panel |
|---|
Image Added |
| Wiki Markup |
|---|
{cloak} |
| id | PNG4 |
|---|
cloak.toggle.type | none |
For each input or output associated with the process unit, Subpart Q requires you to report the following information:
...
When you are finished entering the required information for an input or output, click SAVE. Note, if you are using the carbon mass balance method, you must identify inputs and outputs associated with each process. If you do not, as a reminder you will see a data completeness validation message on the Validation report page as a reminder that you have not completed Unit-Level data entry.
Click image to expand 
| Wiki Markup |
|---|
{cloak:id=PNG5|cloak.toggle.type=none| |
| Cloak |
|---|
cloak.toggle.zone=true} | true
| Panel |
|---|
| id | PNG5 |
|---|
| cloak.toggle.type | none |
|---|
Image Added |
Repeat this step until all inputs and outputs associated with the process unit have been added and defined, then proceed to Step 6.
...
When you are finished entering all required information for the process unit, click SAVE.
Click image to expand 
| Wiki Markup |
|---|
{cloak:id=PNG6|cloak.toggle.type=none| |
| Cloak |
|---|
cloak.toggle.zone=true} | true
| Panel |
|---|
Image Added |
| Wiki Markup |
|---|
{cloak} |
| id | PNG6 |
|---|
cloak.toggle.type | none |
Step 7: Repeat Steps 1-6
Repeat Steps 1-6 until all process units NOT monitored by CEMS have been added for your facility.
...
